Jaw crushers are suitable for any primary and secondary crushing application. It is very productive and efficient. And it is the right solution for increasing your uptime and producing valuable end products. It
can process both hard and soft materials.
Technical Descriptions
Vertical Shaft Crushers; They are crushers with high sand ratio and cubicity ratio, used to obtain 0.5 mm sand and gravel by breaking all kinds of medium-sized hard and abrasive materials. The crushing process takes place by throwing the material fed from the feeding chamber of the crusher to the stone coating in the crushing chamber at high speed by means of the rotor rotating at high speed. Since the feed of the crusher is made by the crusher by hitting the stone with the stone, spare parts consumption is a very economical and cost-effective type of crusher.
Usage Areas
In the crushing of natural stones used in the stream material, in the crushing of the cement material by reducing the size of the materials to be processed in the mill to the maximum ratio, in the crushing of the cement material, in the limestone, basalt and dolomite quarries, if cubic material is desired, in the production of sand, gravel and gravel to be used in the production of concrete asphalt, in the production of road asphalt. It is used to reduce the size of coke added by spraying method to increase the carbon ratio to liquid steel in the production of materials including fine-grained products used in their structures.
These are the machines that purify the finely crushed materials from mud and clay by washing them with water. They are single and double helix. Thanks to the pocket system, it minimizes shaft leakage.
These sieves are generally used between the feeder and the primary crusher. The upper floor is covered with steel grating and the gratings are covered with “V” shaped HARDOX sheet metal. These sieves both act as by-pass sieves in the facility and separate the material that can be crushed by the secondary crusher without going to the primary crusher, thus relieving the primary crusher and increasing its capacity.
They are used in rock feeding. Feeding capacities may vary according to the chamber volumes.
Our GMI Series mobile impact crushers, which are used for breaking medium hard and less abrasive stones, are produced with 3 pendulums. Thanks to these 3 pendulums, it can be used both as a primary and secondary crusher. The crusher, which has a feed size of 600-700 mm, can produce products up to the range of 0-25 mm with the pendulum adjustment. Our machines, which are produced with a complete mobile crusher logic, provide our customers with easy shipping and easy installation.
The new generation mobile crushers are among the most preferred machines of recent years, thanks to their easy and inexpensive installation (installation without the need for curtain concrete and crane). It is produced as 90 or 110 track type tires. Thanks to these features, they are preferred especially in recycling facilities and breaking marble wastes. They are on all evenings and can be transported as a single unit.
It is a crusher with a very high cubic ratio, which is generally used as the first crusher, which enables the stone types of medium hardness and less abrasiveness to be reduced in the primary part as a control of large-sized stones. The crushing process takes place thanks to the impact system of the pallets on the rotor and the linings on the pendulum on the opposite side. By adjusting the intervals between the pendulum and the pallet with a mechanical spring system, the desired small size of material is obtained. They are the crushers that reduce the limestone or limestone, known as less abrasive, below 25 mm or 80 mm in several crushing stages.
Our company, which adds a new dimension to the sieves used in the separation of the crushed materials in the quarries, made a rapid entrance to the market with the horizontal sieves it produced in 2016. Horizontal sieves operating at 0 to 3 degrees, which are produced as a result of R&D studies, have completely eliminated the mixing problem. According to the desired capacity, it can work with a capacity of 50 T/S – 350 T/S. It is driven by two 15/22 kW motors with double drive centers. It can also be produced as mobile trailed type with feeding and discharge bands on the mobile chassis, if desired.
Our extensive range of secondary impact crushers is suitable for reducing and sizing of
soft to medium hard stones and non-abrasive materials. This model can be also used as
primary or tertiary crusher.
They are machines specially designed to produce dust and sand. Rotor with 4 pallets system is used in accordance with the production purpose. The pallets are strengthened with the support system placed behind them. By crashing the impact plates opposite the pallets on the rotor on high speed, the impact plates are mounted on the pendulum with a sliding fitting system. Pendulums can be adjusted mechanically according to the desired product size.
Pallets, counter-impacts and linings can be selected as chrome or manganese alloy depending on the type of material to be used.
Thanks to the covers on its body that can be opened 180 degrees, all kinds of maintenance, repair and replacement procedures can be easily done.
They are used to separate the run-of-the-mill material taken from quarries, mines and streams after crushing. According to the needs, double driven, single driven large size sieves are produced with 15 and 18 angles, as well as dewatering sieves with 3 or 4 angles and flat. Our drive systems are divided into two as top and middle. They can be manufactured with conditional and timing belts.
Horizontal sieves, which have the ability to sift with better quality, are driven by a double drive center. Motors with 2×15 kW and 2×22 kW can be used. It has a screening capacity of 150-300 tons per hour depending on its dimensions.
